SATO CG4 Series Manuel d'instructions Page 31
- Page / 102
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Section 3: Operation and Configuration
CG4 Series Operator Manual Page 3-3
3.2 OPERATING MODES
You can set the printer in any of the following modes:
1.
Normal mode (including Online/Offline modes)
2.
User Test print mode
3.
Factory Test print mode
4.
Operation Setting mode:
• Program download mode
• Font download mode
• Default setting mode
• HEX Dump mode
• USB interface
• RS-232C/ LAN/ IEEE 1284 interface
• Keypad selection
• Scanner, Smart keyboard
You can access the modes by pressing and releasing the POWER button and the FEED/LINE button at
particular points during the ON LINE (POWER) and ERROR indicators’ lighting sequence.
The following flow chart provides a clear summary of each of the modes and its access method.
Printer Start up
Normal Mode
(Online)
Press POWER
button
Power off
Operation setting
Mode
While pressing
FEED/LINE button,
press POWER button
User Test Print
Mode
Holding
FEED/LINE
button
Factory Test
Print Mode
Holding
FEED/LINE
button
Operating Mode ON LINE (POWER) ERROR
Procedures
LED indicator symbols
: Off
: Red light
: Green light
Off
Off
One short beep
Green light
Green light
Red light
Blinking green light
Red light
Printer Start up
Off
Off
Off
Off
One
short beep
Two
short beeps
Three
short beeps
Red light
Release POWER button and
keep holding FEED/LINE
button until the desired mode
lighting pattern is shown.
Holding
FEED/LINE
button
LED indicator responses
Buzzer
- Operator Manual 1
- SATO America, Inc 2
- Safety Precautions 3
- Select a Safe Location 5
- Power Supply 5
- Table of Contents 7
- INTRODUCTION 9
- 1.2.1 Included Accessories 10
- 1.3 PARTS IDENTIFICATION 11
- Back view 12
- Section 1: Introduction 14
- INSTALLATION 15
- 2.2 MEDIA SELECTION 16
- 2.1 SITE LOCATION 16
- 2.3 LOADING LABELS 17
- 2.3 LOADING LABELS (cont’d) 18
- Roll media (Face-in) 20
- Roll media (Face-out) 20
- Fan-fold media 20
- (Printed side face up) 20
- Ribbon unit 21
- Ribbon route 23
- 2.5 CONNECTIONS 24
- 2.5 CONNECTIONS (cont’d) 27
- 2.5.5 Turning On the Power 27
- 2.5.6 Turning Off the Power 27
- Section 2: Installation 28
- OPERATION AND CONFIGURATION 29
- 3.1 OPERATOR PANEL 30
- 3.2 OPERATING MODES 31
- 3.3 USER TEST PRINT MODE 32
- Offset value (Vertical and 33
- Pitch offset value ±099 DOT 33
- 3.4 FACTORY TEST PRINT MODE 36
- Base reference correction 38
- 3.5 OPERATION SETTING MODE 39
- OPERATION SETTING MODE 40
- 3.6 PROGRAM DOWNLOAD MODE 41
- 3.6.1 Firmware Download 42
- 3.7 FONT DOWNLOAD MODE 43
- 3.8 DEFAULT SETTING MODE 44
- 3.9 HEX DUMP MODE 45
- TROUBLESHOOTING 49
- Incorrect 50
- Download 50
- TROUBLESHOOTING TABLE 52
- LIGHT PRINT IMAGES 53
- UNEVEN PRINT DARKNESS 53
- SMEARED PRINT IMAGES 53
- MEANDERING MEDIA 53
- CHK TROUBLESHOOTING STEP 54
- 4.4.1 Hex Dump 55
- 4.4.2 Test label printing 55
- Section 4: Troubleshooting 56
- CLEANING AND MAINTENANCE 57
- I-Mark and Gap 59
- Media guide 59
- 5.4 EASY REPLACEMENT OF PARTS 60
- Fulcrum shaft 62
- Circular 62
- 5.5 ADJUSTING PRINT QUALITY 63
- GENERAL SPECIFICATIONS 65
- PHYSICAL CHARACTERISTICS 65
- POWER SUPPLY (AC ADAPTER) 65
- MODEL NAME 66
- BARCODE CAPABILITIES 69
- STANDARD FUNCTIONS 69
- HARDWARE AND RELATED 70
- REGULATORY COMPLIANCE 70
- CUTTER SPECIFICATIONS 71
- DISPENSER SPECIFICATIONS 71
- INTERFACE SPECIFICATIONS 73
- 7.2 RS232C SERIAL INTERFACE 74
- 7.2.2 Ready/Busy 76
- 7.2.3 X-ON/X-OFF 77
- 7.3.2 Pin Assignments 79
- 7.3.3 Input/Output Signals 80
- 7.4.2 Pin Assignments 81
- 7.4.3 Host Computer Settings 82
- 7.5.2 Software Specifications 84
- 7.5.3 TCP/IP Specifications 85
- 7.5.4 LPD Specifications 85
- 7.5.5 FTP Specifications 85
- 7.5.6 TELNET Specifications 86
- 7.5.7 Setting/Displayed Items 86
- APPENDIX 89
- 8.1.2 Cut position Adjustment 90
- Label output 92
- 8.4 OPERATION MODE SELECTION 94
- Continuous Mode 95
- Tear off Mode 95
- Cutter Mode 95
- Dispenser Mode 96
- Linerless (Non Sepa) Mode 96
- Base reference 97
- 8.7 PAPER END 98
- Feeds 50mm 99
- 8.7.2 Fanfold Label End 99
- Section 8: Appendix 100
- SATO GROUP OF COMPANIES 101
Produits connexes et manuels pour Imprimer et scanner SATO CG4 Series
(114 pages)
(102 pages)
(73 pages)
(73 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.061 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels