Sato CT410 Manuel d'utilisateur Page 124
- Page / 199
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
2. If the product of the values entered for “dd” and “ee” are not equal
to or less than the value of “fff” (i.e.,“ffff” ≥ “dd” x “ee”), an error
will occur and the symbol will not be printed. It is recommended
that these values each be set to “000” and the printer be allowed
to automatically calculate the optimum values.
3. The values for “dd” and “ee” need to be made larger if the security
level is increased.
4. The maximum data length is 2700 characters, but may be less
depending upon:
- the minimum module dimension (“aa”)
- the security level specified by “c”.
- the number of data characters
5. The Reference Point of the PDF417 symbol is the upper-left corner.
6. The <ESC>F Sequential Numbering command cannot be used with
this command.
7. The <ESC>E Line Feed command cannot be used with this
command.
8. The Macro and Truncated PDF417 symbols are not supported.
9. The values 00
H
thru 1F
H
can be specified as print data.
10. This command can be stored in a format.
11. The <ESC>R Rotate command can be used.
12. The print height of the symbol will vary depending upon the data
specified; numeric only, alpha only or alphanumeric.
Section 4. Programming Reference
Page 4-809001069A SATOCTSeriesPrinters
- CT 400 and CT410 1
- Desk Top Printers 1
- APPENDICES 4
- TABLE OF CONTENTS 5
- SECTION 1 9
- PRINTER OVERVIEW 9
- Section 1. Printer Overview 10
- CHARACTER FONTS 12
- BAR CODES 13
- PHYSICAL 14
- OPTIONAL ACCESSORIES 15
- SECTION 2 17
- UNPACKING 18
- SETTING UP THE PRINTER 19
- LOADING RIBBON (CT4XXTT only) 21
- LOADING MEDIA 23
- Paper Sensor 24
- Break Out for 24
- Fanfold Paper 24
- Route Paper under the Sensor 25
- LABEL SENSING 26
- OPERATOR PANEL 27
- REAR CONNECTOR PANEL 28
- CONFIGURATION PANEL 29
- POTENTOMETER ADJUSTMENTS 32
- HEX DUMP DIAGNOSTIC LABEL 35
- PRINT TEST LABELS 36
- SECTION 3 39
- CLEANING AND MAINTENANCE 39
- REPLACING THE PRINT HEAD 41
- CLEANING THE SENSORS 43
- SECTION 4 45
- PROGRAMMING 45
- PROTOCOL CONTROL CODES 46
- USING BASIC 46
- THE PRINT AREA 48
- Table 4.1, Print Area 48
- ROTATED FIELDS 50
- COMMAND DEFAULT SETTINGS 50
- COMMAND CODES 50
- Bar Codes 53
- Input to Printer <ESC>A 54
- Printer Output 55
- UCC-128 Without Incrementing 56
- With Incrementing 56
- Bar Codes, Expansion 58
- Bar Codes, Variable Ratio 59
- Base Reference Point 61
- setting of 62
- Characters, Custom-Designed 63
- Character Expansion 65
- Character, Fixed Spacing 67
- Character Pitch 68
- <ESC>* 71
- Continuous Forms Printing 72
- Copy Image Area 73
- CutCutCut 75
- Left on printerCutCutCut 76
- Cut position 77
- Font/Graphic Recall 80
- Font, Vector 82
- WB & WL Not 84
- Form Overlay, Recall 86
- Form Overlay, Store 87
- Graphics, Custom 88
- Job ID Store 90
- Journal Print 91
- Lines and Boxes 92
- Job Name 94
- Label/Tag Select 95
- Line Feed 96
- Media Size 98
- Off-Line 99
- Print Darkness 101
- Print Position 102
- Print Quantity 104
- Print Speed 105
- Repeat Label 106
- Replace Data (Partial Edit) 107
- Reverse Image 109
- Sequential Numbering 112
- <ESC>A 113
- <ESC>Q50 113
- <ESC>Z 113
- Start/Stop Label 114
- Two-Dimensional Symbols 115
- Two-Dimensional Bar Codes 116
- Data Matrix, Data Format 116
- Data Matrix, Print Data 118
- Maxicode 121
- Implemented 126
- Printer Setting 127
- Default: None 128
- Input to Printer 128
- Print Mode 130
- Print Type 131
- Pitch Offset 132
- Sensor Type 133
- Serial Interface Parameters 134
- SECTION 5 135
- INTERFACE SPECIFICATIONS 135
- THE RECEIVE BUFFER 136
- IEEE 1284 PARALLEL INTERFACE 137
- RS232C Interface Signals 140
- BI-DIRECTIONAL COMMUNICATIONS 142
- SECTION 6 152
- TROUBLESHOOTING 152
- ERROR SIGNALS 155
- APPENDIX A 156
- COMMAND CODE QUICK REFERENCE 156
- 1 Use Dispense offset 162
- 3 Continuous print 162
- - Negative offset 162
- Page 4-88 162
- CT400 CT412 163
- CT400 CT410 165
- APPENDIX B 168
- BAR CODE SPECIFICATIONS 168
- <ESC>BD0bbcccd (data) d 169
- UPC-A/EAN-13 172
- ODD 024680 173
- EVEN 13579CD 173
- Industrial Two of Five 175
- Matrix Two of Five 176
- Code 128 177
- Example Without incrementing 183
- With incrementing 183
- Data Matrix 185
- Character Set 186
- CODE 128 CHARACTER TABLE 189
- Code 128 Character Table 190
- APPENDIX C 192
- CUSTOM GRAPHICS EXAMPLE 195
Produits connexes et manuels pour Imprimeurs Sato CT410
Imprimeurs Sato M10e Manuel d'utilisateur
(82 pages)
(82 pages)
Imprimeurs Sato CG 408 Manuel d'utilisateur
(39 pages)
(39 pages)
Imprimeurs Sato MB400I Manuel d'utilisateur
(27 pages)
(27 pages)
Imprimeurs Sato HT200e Manuel d'utilisateur
(152 pages)
(152 pages)
Imprimeurs Sato GT424 Manuel d'utilisateur
(152 pages)
(152 pages)
Imprimeurs Sato CX208/212 Manuel d'utilisateur
(104 pages)
(104 pages)
Imprimeurs Sato CX400 Manuel d'utilisateur
(26 pages)
(26 pages)
Imprimeurs Sato DR300 Manuel d'utilisateur
(96 pages)
(96 pages)
Imprimeurs Sato XL400/410 Manuel d'utilisateur
(212 pages)
(212 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.635 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels